BERETTA SHOTGUN PARTS-FOREND IRON SPRING PIN (2X10MM) C97060

FOREND IRON SPRING PIN (2X10MM)

SCHEMATIC REFERENCE – S68016, 68218, 69272, DT1020, DT1120, SV10Prevail72, TYPEF14, TYPEG14, COMPACT42, 9507, A30055bis, A39162, A391LIGHT62, 692BE72

PART NUMBER – C97060

Beretta shotgun part FOREND IRON SPRING PIN (2X10 mm) for S680, 682, 692, DT10, DT11, SV10Prevail, TYPEF, TYPEG, COMPACT, 950, A300, A391, A391LIGHT, 692BE

The FOREND IRON SPRING PIN is a component of the forend iron assembly in BERETTA shotguns. It is a small metal pin that holds the forend iron spring in place. The forend iron spring, in turn, provides tension to the forend iron assembly, which is responsible for holding the shotgun’s forend in place.

ELASTIC PIN, INERTIA BLOCK SPRING PIN, C97037

SCHEMATIC REFERENCE – 68291, S680101, 69270, 692BE70, DT10105, DT11105, ASE90101, ASEGOLD105, SV10Perennia70, SV10Prevail70, 471102, 470102, 48656, A30055bis, 7052, A30462, A39052, A39162, AL39162, 80FS54, 9059, 9259, A391LIGHT62, A3000118, A400LC105, A400LS20105

PART NUMBER – C97037

Beretta shotgun part FOREND IRON SPRING PIN for 682, S680, 692, 692BE, DT10, DT11, ASE90, ASEGOLD, SV10Perennia, SV10Prevail, 471, 470, 486, A300, 705, A304, A390, A391, AL391, 80FS, 905, 925, A391LIGHT, A3000, A400LC, A400LS20

Cole Gunsmithing Service Work Order Request Form

Note: It is recommended that all Beretta parts be installed by a qualified and trained gunsmith.

Below are some recommendations from Beretta for cleaning an over under shotgun: Cleaning your Beretta over and under competition shotgun is important to keep it in good condition and ensure it functions properly. Here’s a guide on how to clean a Beretta over and under shotgun:
At the end of a hunting or shotting session, clean the shotgun and make sure the chokes are properly tightened. Metal surfaces on shotguns without protective surface treatment need to be cleaned thoroughly and lubricated after every use to protect against rust. Use a cotton cloth soaked in Beretta gun cleaner and a cleaning rod to remove firing residues from the barrels. Use a bronze brush if necessary. Always insert the cleaning rod into the cartridge chamber. Run a clean, dry cloth through the bores to remove detergent residues. Lightly oil the bores with Beretta gun oil on a clean cotton cloth.
Never apply too much oil. A buildup of oil will attract dirt, and this can interfere with the shotgun’s operation and reliability. lean the inner face of the receiver (especially the area around the firing pin holes) and oil lightly. Do not allow oil to enter the firing pin holes. The hinge pin area is a very important coupling area. The receiver and fore-end iron are subject to very high loads and if not properly oiled, could cause seizing of parts or shotgun malfunctioning. Always make sure these parts are lubricated, following the instructions provided. Carefully clean the outer surfaces of the shotgun to remove all traces of dirt, sweat and fingerprints. Apply a thin layer of gun oil (good quality) to the shotgun, using a soft cloth. WARNING… XCESS OIL OR GREASE CAN OBSTRUCT THE BORE, EVEN PARTIALLY; THIS MAKES FIRING VERY DANGEROUS AND CAN DAMAGE THE SHOTGUN AS WELL AS CAUSING SERIOUS INJURY TO THE SHOOTER AND BYSTANDERS.

BUY YOUR SHOTGUNS FROM THE WORLDS LARGEST BERETTA PREMIUM SHOTGUN DEALER!